Jeld-Wen Custom Windows & Doors Nationwide | TruePane Windows & Doors

Jeld-Wen Custom Windows & Doors in Fort Lauderdale: What to Know First

We install, replace, and service custom windows and doors throughout Fort Lauderdale as an independent provider, not a factory-authorized dealer. Most custom Jeld-Wen jobs run two to four weeks from order to install, depending on whether we’re matching an existing line or building a fully custom opening. Prices typically land between $900 and $3,400 per custom window and $1,800 to $7,500 for a custom door, installed.

Call (954) 280-4413

This page is for Fort Lauderdale homeowners who already own Jeld-Wen products and need straight answers about repair, replacement, or custom work. If you’re standing in front of a window that won’t seal or a door that binds in August humidity, call us at (954) 280-4413 and we’ll walk you through what you’re actually dealing with.

How Jeld-Wen Products Fail - and How We Fix Them

Jeld-Wen builds a broad line, and the failure modes vary by series. In Fort Lauderdale’s salt air and hurricane-season moisture, we see the same patterns year after year. Here are the five we handle most:

• Siteline and Custom Wood Series - veneer separation at the sill. In coastal humidity, the bottom rail of a Jeld-Wen clad-wood window wicks moisture where the aluminum cladding meets the wood. The veneer lifts, the paint blisters, and eventually the sash swells enough to bind. We pull the sash, plane and reseal the rail, re-flash the sill, and reinstall with a drainage gap. If the rot has reached the tenon, we order a replacement sash rather than patch a structural joint.
• Premium Vinyl (the Builder line) - balance shoe failure. The coil-spring balance shoes on Jeld-Wen’s vinyl double-hungs wear out faster in South Florida because fine sand gets into the track. The window drops hard, and the homeowner assumes it needs replacing. Most of the time it’s a $40 balance shoe and an hour of labor. We also check the tilt latches while we’re in there; those crack from people forcing a stuck sash.
• Custom Wood and Siteline casement windows - operator gear stripping. Jeld-Wen casement cranks use a zinc gear that strips when the sash is out of plane. Instead of addressing the geometry, most handymen swap in a new crank, which strips again in a year. We reset the hinge track, shim the sash true, and only then install the replacement operator. The crank lasts because the window now closes square.
• Auraline composite doors - thermal bowing in direct sun. Fort Lauderdale’s western exposures hit Auraline slabs with full afternoon sun, and the composite skin expands at a different rate than the foam core. The door bows and won’t latch by late afternoon. In most cases, we correct it with hinge-side shimming and a new threshold sweep rather than replacing the slab. If the bow has taken the frame out of square, we’ll reset the rough opening while we’re there.
• W-2500 and Premium Wood series windows - leaky glazing seals. The glazing bead on these older Jeld-Wen lines dries out and lets water behind the glass. The unit fogs, the IGU fails, and you’re looking at full glass replacement, not a sash swap. We measure the glass pack, order an exact-match IGU with the correct low-E coating, and reset it in the original sash. The frame, the aluminum cladding, and the interior trim all stay put.

One thing we do on every Jeld-Wen job: we look for the factory label on the head jamb. The serial number and model code tell us the exact plant, the glass spec, and the production year. That’s how we avoid mismatched glass coatings that read fine on paper and look wrong on the wall.

Our Jeld-Wen Custom Windows & Doors Process

Here’s how a Jeld-Wen custom job runs through our shop, start to finish:

1. 1
   Site visit and measurement. A technician measures every opening twice, checks the rough frame for square, and notes any water intrusion at the sill. If Dale Kessler happens to be on the job, he’ll tell you the rule he learned from his father in Sailboat Bend: if it is not right on paper, it will not be right on the wall.
2. 2
   Product decision. We lay out your options side by side: OEM Jeld-Wen parts and sashes, a full factory replacement order, or a quality aftermarket equivalent from one of our other lines when it fits better. You see the difference in writing, including warranty terms.
3. 3
   Order and lead time. Custom Jeld-Wen units run two to four weeks from order. Standard parts are usually in our shop within three to five business days.
4. 4
   Installation. We remove the old unit, correct any framing issues at the rough opening, flash and seal per Fort Lauderdale code, and set the new window or door true. We don’t caulk over a problem and call it done.
5. 5
   Cleanup and walkthrough. We test the lock, the seal, and the operation with you standing there. You sign off, we register both warranty layers in writing, and the truck leaves your driveway.
6. 6
   Follow-through. If anything isn’t right in the first 90 days, we come back and fix it. No paperwork, no arguing. That’s the Done Right Promise.

What Jeld-Wen Custom Windows & Doors Costs in Fort Lauderdale

Custom Jeld-Wen work is priced by the opening, not by the square foot. Here’s what our customers in Fort Lauderdale typically see:

• Custom single window (clad-wood or premium vinyl): $900 to $3,400 installed
• Custom casement or picture window with architectural grilles: $1,400 to $4,800
• Custom entry door (wood or Auraline): $1,800 to $7,500
• Custom patio slider or French door: $3,200 to $9,000
• Commercial storefront glazing or curtain wall work: quoted per project, typically $12,000 and up

What moves the price: whether we can rebuild the existing frame or need to open the rough opening, the glass spec (impact-rated adds meaningful cost), the interior finish, and whether the project is on the ground floor or requires staging. We give you the total in writing before any work starts. Call (954) 280-4413 and we’ll put a real number on your job, free.

Why Fort Lauderdale Homeowners Call TruePane Windows & Doors for Jeld-Wen Work

We’ve been serving this community since 2008, and we approach every Jeld-Wen job the same way we’d approach a window in our own mother’s house. Our technicians are background-checked and uniformed. They measure every opening twice. They quote manufacturer lines side by side on paper so you see exactly what you’re buying. And they register both warranty layers in writing before the truck leaves your driveway. That’s The Keystone Standard, and it’s been our baseline since Dale Kessler started this company in 2008.

If a Jeld-Wen replacement doesn’t make sense on a given opening, we’ll tell you and show you alternatives from Andersen, Pella, or PGT. We’re not selling one brand; we’re solving your problem. And if something isn’t right inside 90 days, we fix it. We stand behind it.

FAQs