Free in-home measure and quote - PGT, CGI and CWS impact lines compared on your actual openings, style by style
Sliding glass doors
Impact garage doorsPGTCGI
Before
After
Before
After
Before
AfterCGI Glass Railing Systems in Fort Lauderdale: What to Know First
CGI glass railing systems in Fort Lauderdale are impact-rated aluminum and heavy glass assemblies built for the same wind zones as CGI windows and doors, and most repairs we handle involve a loose top rail, a shifting glass panel, or spalled hardware from salt air. We are an independent CGI service provider, not a manufacturer affiliate, and our techs have worked on CGI glass railing systems from Rio Vista to Coral Ridge since we opened our doors. A typical repair runs $250 to $1,200 depending on the series and what failed, and we quote it in writing before any work starts. Call (954) 280-4413 for a free estimate.
How CGI Products Fail - and How We Fix Them
- Loose top rails on CGI frameless glass rail systems. The top rail on older CGI frameless series relies on set screws and compression blocks that work loose over years of thermal cycling in Fort Lauderdale heat. Wind vibration against the glass makes it worse. We re-torque, replace the blocks, and reseat the rail so the glass stops rattling in the channel.
- Corroded aluminum posts where the base plate meets concrete. Salt air near Fort Lauderdale’s intracoastal and beachfront corridors eats at raw aluminum, especially at the base plate where water pools. We see it on elevated decks facing the water. The fix is removing the corrosion, treating the area, replacing the base plate if it’s beyond saving, and resealing with marine-grade sealant.
- Cloudy or spalled glass infill panels on CGI rail systems. Impact glass can delaminate or cloud when the interlayer breaks down, a slow failure that typically shows up after ten or more years in direct sun. We replace infill panels with like-kind impact-rated glass and register the new panel under its own warranty.
- Lost or stripped hardware on adjustable glass clamps. CGI’s adjustable clamps on some older series use small stainless set screws that seize against the salt and then strip when back pressure is applied. We extract them without damaging the surrounding aluminum, re-tap where needed, and replace with anti-seize coated stainless to prevent a repeat.
- Gate sag on CGI glass railing gate assemblies. Glass gate panels are heavy, and the self-closing hinge hardware on CGI gate posts wears at the hinge pin. The gate starts scraping the deck or latches poorly. We rebuild the hinge, realign the panel, and adjust the closer so the gate shuts the way it did when it was new.
Our CGI Glass Railing Systems Process
When you call TruePane Windows & Doors about a CGI glass railing system, here’s what happens. If it is not right on paper, it will not be right on the wall.
- 1
We come out and look at the whole run. Not just the one panel you pointed to. A loose panel is often a symptom of something happening at the other end of the run.
- 2
We identify the series and the failure. CGI has manufactured multiple railing lines over the years, and the parts are not interchangeable. We find the sticker, we check the extrusion profile, and we match the spec.
- 3
We quote OEM and quality aftermarket options side by side on paper. Some repairs are factory-spec only if you want to preserve a warranty. Some are better served by aftermarket hardware that outperforms the original in salt air.
- 4
We do the work. Most CGI railing repairs are completed in a single visit. We carry the common hardware and sealants for these jobs on the truck.
- 5
We test every panel and the gate. The glass should sit square, the rails should be tight, and the gate should operate without binding.
- 6
We document the repair and register any new parts under warranty. The Keystone Standard means both warranty layers go in writing before we leave, and the Done Right Promise covers the workmanship.
What CGI Glass Railing Systems Costs in Fort Lauderdale
CGI glass railing work in Fort Lauderdale is priced by what failed, not by square footage. Here’s what we typically see:
- Hardware retorque and set screw replacement: $250-$450
- Base plate replacement with corrosion treatment: $500-$900 per post, depending on access
- Single glass infill panel replacement (impact-rated): $700-$1,200
- Glass gate hinge rebuild and realignment: $400-$700
- Complete short-run glass railing replacement: $2,000 and up, depending on linear footage and series
What moves the price: deck height and access, the CGI series you have, whether the glass is flat or shaped, and the condition of the surrounding posts. We honor a permanent 5% discount for seniors and veterans and a $50 credit on any repair over $250. Call (954) 280-4413 for a free, written estimate.
Why Fort Lauderdale Homeowners Call TruePane Windows & Doors for CGI Work
Dale Kessler grew up in Sailboat Bend, learned the trade at McFatter Technical College, and has been working glass in South Florida’s coastal corridor for the better part of two decades. Our techs know CGI hardware the way a mechanic knows a specific engine block, and we carry the right fasteners, sealants, and shims for these systems. We also install and service Andersen, Pella, and PGT, so when a repair crosses into replacement territory, we can show you the real options side by side on paper. Every job is backed by our Done Right Promise, both warranty layers are registered before the truck leaves your driveway, and a live person answers the phone 24 hours a day, every day. We’ll be there when we say.
FAQs
Yes. We are an independent CGI service provider, which means we work on CGI railing systems regardless of who installed them originally. We identify the series, source the correct parts, and make the repair without any requirement of an existing relationship with the original contractor.
It depends on the repair and the parts used. When factory-spec parts are available and the warranty is still active, we use OEM. When the original hardware has been discontinued, we offer aftermarket options and tell you plainly what that means before we touch anything. Call (954) 280-4413 if you’re unsure what your warranty still covers.
Most railing repairs are scheduled within days, and a live person answers our phone 24/7 to take your call. Some jobs, like a loose panel that’s still in place, can wait a few days without issue. Some jobs, like a gate that won’t latch or a panel that’s moved out of its channel, should be handled sooner. Call us and we’ll be direct about the timing.
If the aluminum extrusions are sound and the problem is hardware, glass, or a single post, repair makes sense. If corrosion has spread through multiple posts or the glass is delaminating in several panels, replacement may be the better dollar. We will walk you through both numbers before you commit to either. Call (954) 280-4413 for an honest assessment.
Written by Dale Kessler, Owner, TruePane Windows & Doors at TruePane Windows & Doors, serving Fort Lauderdale and nearby areas.
Six Reasons Homeowners Choose TruePane Windows & Doors
Impact systems engineered to design pressures up to +/-100, matched to your wind zone - your openings hold when the storm arrives.
Low-E insulated impact glass from our manufacturer lines commonly cuts monthly cooling bills 20-30%.
Laminated impact glass shuts out up to 40% of outside noise - traffic, neighbors, weather.
Monitoring services run $30-90 a month. Laminated impact glass resists forced entry around the clock, with no subscription.
Florida homeowners average around 25% savings on the windstorm portion of their policy after protecting every opening - some homes qualify for more.
A full impact package upgrades curb appeal, buyer confidence and appraised value in one project.